How to make an ax out of a kangaroo. Instruction

The ax will be made from the bones of a kangaroo, shit kangaroo, ash and tar.
This skill will be very useful to you if you are planning to travel around Australia, so please take everything shown in the post with all seriousness.
So a detailed photo and video instruction under the cut.
Kangaroo bone ax, kangaroo shit, ash and tar
2. Arriving in Australia, passing passport control and filling out a quarantine declaration, immediately go to the nearest national park to find the necessary components from which you will make an ax.
A big tibial bone and a scapula of a kangaroo, a little of kengurin shit, common ash and wood resin will be needed for the van ....
Kangaroo bone ax, kangaroo shit, ash and tar
3. The most difficult thing in this case is to find a frozen tree resin. In principle, any resin will do, but Australia has thickets of trees along the roads, something like a palm tree - with a thick crown of leaves. It is necessary to find dried trunks, and it is there either to look for the fallen pieces of bark with the bases of the leaves that have already turned to stone from the hardened resin, or to pick them off.Well, and then "disassemble" them into parts, separating the petrified drops of resin (at the end of the video this moment is shown in more detail).
This resin will become the main glue, which we will join to pieces of the ax
Kangaroo bone ax, kangaroo shit, ash and tar
4. Shit kangaroo in Australia is quite easy to find - it is lying everywhere, because kangaroos are found throughout the country.
Dry shit will be the basis of glass wool, which has a binding and filling function for a tight fit of the details of the future weapon.
To make glass wool from shit, you need to crush it well ...
Kangaroo bone ax, kangaroo shit, ash and tar
5. Then you need to crush the ordinary wood ash ....
Kangaroo bone ax, kangaroo shit, ash and tar
6. And crush the resin. Then mix all three ingredients and mix well.
Kangaroo bone ax, kangaroo shit, ash and tar
7. Copies of glue should have the following consistency.
Kangaroo bone ax, kangaroo shit, ash and tar
8. Now we collect firewood and kindle a small fire. On it we will melt the components of the glue and connect the parts of the ax
Kangaroo bone ax, kangaroo shit, ash and tar
9. Now we heat the bone (it’s an ax handle) in the place where the head of the bone has a flat platform, then sprinkle the heated part with glue mixture, heat this place on the fire so that the mixture will melt and sprinkle again. We do this a sufficient number of times so that the surface of the bone is covered with a good saturated adhesive layer.
Kangaroo bone ax, kangaroo shit, ash and tar
ten.When the glue on the handle a lot, put a spatula and squeeze strongly for several tens of seconds.
Let's wait until the ax is stuck and prodorzhly heat on the fire, pour in our glue mixture in the cavity between the parts to fill all the voids.
Kangaroo bone ax, kangaroo shit, ash and tar
11. Well, in the end it remains only to let the ax cool down and can be used for its intended purpose.
On what? Yes FIG knows.
I just do not know why and to whom this ax is needed in our time.

Related news

How to make an ax out of a kangaroo. Instruction image, picture, imagery


How to make an ax out of a kangaroo. Instruction 48


How to make an ax out of a kangaroo. Instruction 32


How to make an ax out of a kangaroo. Instruction 45


How to make an ax out of a kangaroo. Instruction 68


How to make an ax out of a kangaroo. Instruction 8


How to make an ax out of a kangaroo. Instruction 34


How to make an ax out of a kangaroo. Instruction 35


How to make an ax out of a kangaroo. Instruction 70


How to make an ax out of a kangaroo. Instruction 9


How to make an ax out of a kangaroo. Instruction 88